BLK Audiovisual LTD | Desktop Mixers

USED EQUIPMENT

Sell your used Equipment

Digital TF5

33 motor faders (32 channels + 1 master)
48 input mixing channels (40 mono + 2 stereo + 2 return)
20 Aux (8 mono + 6 stereo) + Stereo + Sub buses
8 DCA groups with Roll-out
32 analog XLR/TRS combo mic/line inputs + 2 analog RCA pin stereo line inputs
16 analog XLR outputs
34 x 34 digital record/playback channels via USB 2.0 + 2 x 2 via a USB storage device
1 expansion slot for NY64-D audio interface card

Fader Configuration		32 + 1 (Master)
Mixing Capacity	Input Channels	48 (40 mono + 2 stereo + 2 return)
	Aux Buses	20 (8 mono + 6 stereo)
	Stereo Buses	1
	Sub Buses	1
Input channel functions		8 DCA Groups
I/O	Inputs	32 mic/line (XLR/TRS combo) + 2 stereo line (RCA pin)
	Outputs	16 (XLR)
	Expansion slots	1
On-board processors	DSP	8 Effects + 10 GEQ
USB		34x34 USB Audio Interface, 2-track recording via USB Storage Device

General specifications

Sampling frequency rate	Internal	48 kHz
Signal delay		Less than 2.6 ms, INPUT to OMNI OUT, Fs=48 kHz
Fader		100 mm motorized, Resolution = 10-bit, +10 dB to –138 dB, –∞ dB all faders
Total harmonic distortion		Less than 0.05% 20 Hz–20 kHz @+4 dBu into 600 , INPUT to OMNI OUT, Input Gain=Min. (Measured with a –18 dB/octave filter@80 kHz)
Frequency response		+0.5, –1.5 dB 20 Hz–20 kHz, refer to +4 dBu output @1kHz, INPUT to OMNI OUT
Dynamic range		110 dB typ., DA Converter, 107 dB typ., INPUT to OMNI OUT, Input Gain=Min.
Hum & noise level	Equivalent input noise	–128 dBu typ., Input Gain=Max. (Measured with an A-Weight filter)
Hum & noise level	Residual output noise	–85 dBu, ST master off (Measured with an A-Weight filter)
Crosstalk		–100 dB (Measured with a –30 dB/octave filter@22 kHz), adjacent INPUT/OMNI OUT channels, Input Gain=Min.
Power requirements		100–240 V 50/60 Hz
Power consumption		120 W
Dimensions	W	866 mm (34.1in)
	H	225 mm (8.9in)
	D	599 mm (23.6in)
Net weight		20.0 kg (44.1lb)
Accessories		Quick Guide, Power Cord, CUBASE AI download information
Options		Expansion Card, Foot Switch (FC5)
Others		Operating temperature range: 0–40 °C, Storage temperature range: -20–60 °C

Analog input characteristics

Input Terminals	GAIN	Load Impedance	For Use With Nominal	Input Level			Connector	balanced / Unbalanced
Input Terminals	GAIN	Load Impedance	For Use With Nominal	Sensitivity*1	Nominal	Max. before clip	Connector	balanced / Unbalanced
INPUT1-32	+66dB	7.5KΩ	50-600Ω Mics or 600Ω Lines	-82dBu (61.6V)	-62dBu (0.616mV)	-42dBu (6.16mV)	Combo Jack (XLR-3-31 type 2 or TRS phone 3)	Balanced
INPUT1-32	-6dB	7.5KΩ	50-600Ω Mics or 600Ω Lines	-10dBu (245mV)	+10dBu (2.45V)	+30dBu (24.5V)	Combo Jack (XLR-3-31 type 2 or TRS phone 3)	Balanced
ST IN 1,2	—	10kΩ	600Ω Lines	-30dBV (31.6V)	-10dBV (316mV)	+10dBV (3.16V)	RCA Pin Jack	Unbalanced

*1. Sensitivity is the lowest level that will produce an output of +4dBu (1.23V) or the nominal output level when the unit is set to maximum gain. (All faders and level controls are at maximum position.)
*2. 1: GND, 2: HOT, 3: COLD
*3. Tip: HOT, Ring: COLD, Sleeve: GND
*In these specifications, 0dBu = 0.775Vrms.
*+48V DC (phantom power) can be supplied to INPUT XLR type connectors via each individual software controlled switch.

Analog output characteristics

Output Terminals	Source Impedance	For Use With Nominal	Output Level		Connector	balanced / Unbalanced
Output Terminals	Source Impedance	For Use With Nominal	Nominal	Max. before clip	Connector	balanced / Unbalanced
OMNI OUT 1-16	75Ω	600Ω Lines	+4dBu (1.23 V)	+24dBu (12.3 V)	XLR-3-32 type *1	Balanced
PHONES *3	100Ω	40Ω Phones	3mW	75mW	Stereo Phone Jack (TRS) *2	Unbalanced

*1.1: GND,2: HOT, 3: COLD
*2 Tip: LEFT, Ring: RIGHT, Sleeve: GND
*3 The position of the level control is lowered by 16dB from the maximum.
*In these specifications, 0dBu = 0.775Vrms.
*All output DA converters are 24bit, 128times oversampling.